Skip to content

Why doesn't a newsletter reach someone?

Before sending a newsletter, Powergest checks every address and leaves out the ones that shouldn't receive it, recording the reason. This page explains each reason, which ones can be overridden and which can't. The newsletter itself tells you how many are left out for each reason, and each address's record in Mailing → Addresses tells you which one applies today. At the end you'll find what changes when you're sending invoices or other documents.

Where can I see why an address doesn't receive it?

In three places:

If several reasons apply, the most serious is shown: first the ones that can't be overridden.

Which reasons leave an address out?

ReasonWhat it meansCan it be included?
Marked an email as spamThe person marked it as spamNever
UnsubscribedThey asked not to receive marketing emailsNever in a newsletter
The mailbox does not exist (invalid address)Hard bounce, or the clean-up of a verification that proved it doesn't existNever
Marked as ‘Do not resend’Your company decided not to write to them, manually or when cleaning up with a verification (the reason starts with "Verification:")Never, while it's marked
Not a customer and has not given consentIt's a prospect without consentNever, if your company requires it
Suspended due to bouncesThree soft bounces in a rowYes, with addresses with failures
Its quality is below the sending thresholdQuality below 40Yes, with addresses with failures

Which reasons does the newsletter itself add?

On top of the address's own reasons, each newsletter leaves people out on its own account:

ReasonWhat it meansCan it be included?
Has no email address (or it is not valid)The record or contact has no email, or what it has isn't an address. In a list, also a record that has none of the emails the list asks forBy adding a valid email to its record, or by ticking other emails of the record in the list
The address appears more than once: it gets only one emailIt comes through two routes (its record and its CRM contact, two records, a list and a criterion…)No need: the email reaches them through the other route
Unsubscribed from this topicThey don't want to receive the newsletter's topic (its campaign's, its own or its template's)Never in a newsletter on that topic
Already received a newsletter from this campaignThe campaign has Don’t repeat recipients ticked and it was already sent to them, or is scheduledBy unticking it in the campaign
The plan’s email limit was reachedYour plan doesn't allow sending emails outsideBy changing plan
You left it outIt meets something in the newsletter's Who to leave out, or in a segment it chose (for example, they're already a customer)By removing that criterion

Unsubscribing from the topic takes priority over "include addresses with failures": a suspended address that has also unsubscribed from the topic stays out.

Adding someone manually to the newsletter doesn't override any of these reasons.

What if they unsubscribe after the newsletter is launched?

It doesn't reach them. A newsletter scheduled for a few days' time, or a large one that takes several days to go out because of the sender's daily limit, checks each address again just before sending to it. If since the launch the person has unsubscribed, unsubscribed from the topic, marked an email as spam or their mailbox turned out not to exist, they are Excluded with that reason instead of receiving it.

What if the email went out but didn't reach them?

Then the recipient's status in the newsletter's monitoring tells you:

What the program does in each case is in monitoring a newsletter. The server accepting it (Sent) doesn't guarantee that it lands in the inbox: the recipient's mailbox may send it to spam. The warnings about the domain in the senders help to avoid this.

What is "include addresses with failures"?

It's a newsletter option, in More options. With it, suspended and low-quality addresses are included too: it's for an important notice that you want to try to get to everyone. Unsubscribes, complaints, invalid addresses, addresses marked "Do not resend" and prospects without consent are never included: that isn't a mailbox failure, it's a decision by the person, the law or your company.

And when I send invoices or other documents?

An ERP document (an invoice, a delivery note) isn't advertising: it's part of your relationship with your customer. That's why unsubscribes (from everything or from a topic), consent, quality and "already received a newsletter from this campaign" don't count, and two invoices for the same customer aren't a "repeated address": each one goes in its own email, or both in one if the send groups by customer. What does count is complaints, invalid addresses, suspension (unless the send includes suspended addresses), "Do not resend", the plan limit and one reason of its own for documents:

ReasonWhat it meansCan it be included?
The PDFs exceed the maximum attachment sizeThe PDFs in that email add up to more than your company allows (15 MB unless it's been changed)By sending them ungrouped, or by raising the maximum in the settings

A document that doesn't go out because its address is invalid, because its PDF couldn't be generated or because of its size is also flagged in the notifications bell. See sending invoices and other documents by email.

How do I get it to reach them again?

It depends on the reason:

More about Mailing